Welcome to 3D Arts (a 3D Printing Co.)
We Teach 3D Printing to all ages one to one or group any time any day no prior qualification require !

Stepper motor driver board with ULN2003 and Step Motor 28BYJ-48



 Sold Out 

  • Description
  • Details
  • Reviews

Stepper motor driver board with ULN2003 and Step Motor 28BYJ-48

A, B, C, D four-phase LED indicates the status of the stepper motor work.
Stepper motor with a standard interface, when used directly pluggable.
Drive Module Board Size:2.8cm x 2.8cm x 2cm 
Signal Output function :
Brand new and high quality.
Voltage: 5V.
Diameter: 28mm.
Step angle: 5.625 x 1 / 64.
Reduction ratio: 1 / 64.
5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for.
supporting the use of easy to use stepper motor used in the development board.
Dimensions of the Board : 31mm × 35mm.
Stepper motor driver board with ULN2003.
A, B, C, D four-phase LED indicates the status of the stepper motor work.
Stepper motor with a standard interface, when used directly pluggable.
Drive Module Board Size:2.8cm x 2.8cm x 2cm - 1.1inch x 1.1inch x 0.79inch.
Stepper motor Size:3.2cm x 3.2cm - 1.26inch x 1.26inch.

ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR AR​​M
Drive Module Board ULN2003
Stepper motor 

Hooking it up to the Arduino
Connect the ULN2003 driver IN1, IN2, IN3 and IN4 to digital pin 3, 4, 5 and 6 respectively on the Arduino Uno. Connect the positive lead from a decent 5-12V battery pack to the “+” pin of the ULN2003 driver and the ground to the “-” pin. Make sure that the “on/off” jumper next to the “-” pin is on. If you power the Arduino from a different battery pack, connect the grounds together.

The ULN2003 stepper motor driver board allows you to easily control the 28BYJ-48 stepper motor from a microcontroller, like the Arduino Uno. One side of the board side has a 5 wire socket where the cable from the stepper motor hooks up and 4 LEDs to indicate which coil is currently powered. The motor cable only goes in one way, which always helps. UNL2003 board On the side you have a motor on / off jumper (keep jumper on to enable power to the stepper). The two pins below the 4 resistors, is where you provide power to the stepper.
Data Sheet
(Note that powering the stepper from the 5 V rail of the Arduino is not recommended).

A separate 5-12 Vdc 1 Amp power supply or battery pack should be used, as the motor may drain more current than the microcontroller can handle and could potentially damage it. In the middle of the board we have the ULN2003 chip. At the bottom are the 4 control inputs that should be connected to four Arduino digital pins.

tutorials/28byj-48-stepper-motor

Keywords:
ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR AR​​M
Drive Module Board ULN2003
Stepper motor 

arduino/AccelStepper

 

  • Model: 28BYJ-48
  • 0 Units in Stock

Be the first to write a review.  Write a Review.

This product was added to our catalog on Sunday 03 January, 2016.

Important Links

Sponsors

Happy Holidays, Happy New year 2016

3d Printing - training - courses

Who's Online

There currently are 2 guests online.
Your IP Address is: 54.158.80.117
View 3D ARTS's profile on LinkedIn
Content

Every One Special here

We are first in the world who start teaching - How to build 3D Printers.
We help you to create some thing new every day.
Customize Clasese One on one or group



We create inventors